Metalu B2 pool lift

Metalu B2 pool lift is the safest pool lift in the market thanks to its handrail and 5 support points.

No need for instalation work. No matter the pool situation (full, empty, on site, etc.). Installation is very simple, you only need a water connection and anchors on the outside of the pool.

Features - Metalu B2 pool lift

+ Approved to lift 150 and 120 Kgs.

+ For its operation, a water supply with pressure at 5.5 bar is necessary.

+ To lift 150 Kgs, a water intake with a pressure of 5; 5 bar is required.

+ To lift 120 Kgs. Only 3.5 bar is needed.

+ Turning angle: 170º, clockwise (downhill).

+ Turning radius 700 m/m.

+ The drive control is located to the right of the user.

+ The seat has a travel of 1.06 meters. and it is adjustable in height, normally it is placed at +0.53 meters. and -0.53 mts. above the water level.

+ It adapts to any pool because all catches are adjustable

+ Net weight - 50 Kg

+ Packed weight - 62 kg

+ Empty rise time - 20 seconds

+ Rise time with 85 kg load - 25 seconds

+ Empty down time - 42 seconds

+ Lowering time with 85 kg load - 20 seconds

+ Water capacity in the piston - 8 liters

Pre-Installation and Installatio - Metalu B2 pool lift

When choosing the location site, the following points must be taken into account:

+ Make it easy for the user to access.

+ That it is not in place of transit or parking by other bathers.

+ That the water intake is as close / comfortable as possible.

+ We recommend putting the elevator where the water has a depth of 1.20/1.30 meters approx. In order if the user of the elevator needs help, the person who accompanies it is sure to stand.

+ In the place where it has been decided to place the elevator, it is necessary to leave a water connection of ½ inch and 3.5 bar. If the network did not have such pressure, a pressure group would have to be installed.

+ If the pool is already built, we recommend putting the water inlet after placing the lift.

+ The installation is very simple.

+ It only has anchors on the outside of the pool.

+ Adjust the height of the seat and connect the hose to the water connection.

Tips for better use and maintenance - Metalu B2 pool lift

+ The list must be cleaned periodically, as the faucets in houses are cleaned. If the dirt is very encrusted, use Viakal gel, or similar, and ceramic ceramic scotch-brite. This way METALU will always be like the first day.

+ Keep in mind that there is chlorine, lime and dirt in the water, the water evaporates leaving the dirt on the METALU surface.

+ If the lift is not used, it must be periodically operated under load by raising and lowering it several times.

+ At the end of the season, the lift must be stored in a place where it does not receive blows or damage, leaving the piston empty (at the bottom) and drying it with a cloth.

+ In frost risk areas during winter it is essential to empty the hoses and the water piston.

+ For the operation of the elevator use clean water, if you use well water or another place that may contain impurities, use filters.

+ If the ELECTROLYSIS system is used for water treatment, we recommend connecting the lift to an earth connection.

+ At the beginning of the season, the water intake hose must be purged

Indoor pools:

+ If the lift is used in an indoor pool, cleaning is essential.

+ Compared to outdoor swimming pools, in addition to higher water and air temperatures, they tend to show lower levels of renewal of these elements and, frequently, a higher intensity of use. All this translates into a greater load of bathers, greater organic contamination and, consequently, higher doses of disinfectant products.

These products contain volatile particles that condense in poorly ventilated air, adhering to metal surfaces. Therefore, it is recommended that the elevator be cleaned often by rinsing it with non-saline, chlorine-free water (mains water).